Tattu 18000mAh 6S1P 22.2V 15C Smart Lipo Batt w-AS150+XT150 plug

Specifications:

Minimum Capacity: 18000mAh

Configuration: 6S1P / 22.2V / 6Cell

Discharge Rate: 15C

Max Burst discharge Rate: 30C

Net Weight(±20g): 2270g

Dimensions: 205.5mm Length x 94.2mm Width x 79.5mm Height

Discharge Plug: AS150+XT150 plug

Charge Plug: XT90
 

Features:

Overheat protection

Low temperature protection

Over voltage protection

Over current protection

Intelligent Storage:

Normal temperature range storage     

 Above normal temperature storage 60-70? (158°F –176°F) 

 Hot conditions storage 70-80? (158°F – 176°F)

Local after-sales service(located in Dublin, CA)

Brand Tattu

Capacity(mAh) 18000

Voltage(V) 22.2

Discharge Rate (C) 15

Max Burst discharge Rate (C) 30

Configuration 6S1P

Net Weight(±20g) 2270

Length(±5mm) 205.5

Width(±2mm) 94.2

Height(±2mm) 79.5

Connector Type AS150+XT150 plug

Wire Gauge 8#

Discharge Wire Length(mm) 120

Balancer Connector Type XT90

Balancer Wire Length(mm) No

Function Comparison between Tattu Plus and Tattu Plus 2.0

 

Feature

Tattu Plus 

Tattu Plus 2.0

 

Fuel Gauge

YES

Yes, the fuel gauge is run by a very accurate coulomb meter and impedance tracking circuit. 
This makes the fuel gauge display very precise.

 

Self Balance in storage mode

YES

Yes, the pack will self balance the individual cells depending on the SOC(State of charge) difference during storage mode

Discharge Low voltage warning

LED Flash Warning

Audible warning system

Discharge over temperature warning

LED Flash Warning

Audible warning system

 

Cycle life indicator

NO YES

Defective Pack Warning

NO if you click the pack button and the fuel gauge shows red L.E.D.s, it is time to replace this pack
.

Battery low voltage warning

NO

Yes, if you click the button and the fuel gauge shows yellow L.E.D.s the pack voltage is low and you need to recharge.

 

Battery storage indicator

NO

Yes, The storage is turned on if you click the button and the fuel gauge shows white L.E.D.s  the pack is in storage mode.

 

Advanced charging protection

NO  

Yes, if the pack individual cell voltage is too low when charging is started,the BMS will limit the incoming charge current to  battery until the voltage is correct, then accept full supplied charge current

 

Voltage Overcharge Protection 

NO 

Yes, the overcharge protection circuit will activate when any cell voltage exceeds the factory set failsafe values.

 

Charging over current protection 

NO 

Yes, charging over current protection circuit will be activated when charging current reaches factory set failsafe values.  The protection circuit will remain active until charger is disconnected.

 

Charging short circuit protection 

NO 

Yes, the protection circuit will cut off charging when it detects that the current reaches the factory set short-circuit protection limit. When protection is triggered all FETs will be turned off.

 

High Temperature Charge Protection 

NO 

Yes, if the pack temperature exceeds factory set values It will not charge.  When the pack is back in the correct temperature range it will charge normally

 

Low Temperature Charge Protection

 NO  

Yes, if the pack temperature falls below factory set values the pack will not charge.  When the correct temperature is back in range the pack will charge normally.

 

Secondary Charge Protection

 NO  

Yes, Tattu Plus 2.0 has a secondary charging protection circuit.  If the first level circuit has a failure, the second level of protection will cut the charging circuit off

 

IIC communication port

 NO  

Yes, The IIC communication port is active.  When you connect the batterypack to the computer software the IIC will allow you to read: pack voltage, individual cell voltage, rated capacity after full charge, remaining capacity, capacity percentage, cycle time, tem