Tattu Plus2.0 18000mAh 6S1P 22.2V 15C Smart Lipo Battery with AS150+XT150 plug TA-PLUS2.0-15C-18000-6S1P
Specifications:
Minimum Capacity: 18000mAh
Configuration: 6S1P / 22.2V / 6Cell
Discharge Rate: 15C
Max Burst discharge Rate: 30C
Net Weight(±20g): 2270g
Dimensions: 205.5mm Length x 94.2mm Width x 79.5mm Height
Discharge Plug: AS150+XT150 plug
Charge Plug: XT90
Features:
Overheat protection
Low temperature protection
Over voltage protection
Over current protection
Intelligent Storage:
Normal temperature range storage
Above normal temperature storage 60-70? (158°F –176°F)
Hot conditions storage 70-80? (158°F – 176°F)
Local after-sales service(located in Dublin, CA)
Brand Tattu
Capacity(mAh) 18000
Voltage(V) 22.2
Discharge Rate (C) 15
Max Burst discharge Rate (C) 30
Configuration 6S1P
Net Weight(±20g) 2270
Length(±5mm) 205.5
Width(±2mm) 94.2
Height(±2mm) 79.5
Connector Type AS150+XT150 plug
Wire Gauge 8#
Discharge Wire Length(mm) 120
Balancer Connector Type XT90
Balancer Wire Length(mm) No
Function Comparison between Tattu Plus and Tattu Plus 2.0
Feature
Tattu Plus
Tattu Plus 2.0
Fuel Gauge
YES
Yes, the fuel gauge is run by a very accurate coulomb meter and impedance tracking circuit.
This makes the fuel gauge display very precise.
Self Balance in storage mode
YES
Yes, the pack will self balance the individual cells depending on the SOC(State of charge) difference during storage mode
Discharge Low voltage warning
LED Flash Warning
Audible warning system
Discharge over temperature warning
LED Flash Warning
Audible warning system
Cycle life indicator
NO YES
Defective Pack Warning
NO if you click the pack button and the fuel gauge shows red L.E.D.s, it is time to replace this pack
.
Battery low voltage warning
NO
Yes, if you click the button and the fuel gauge shows yellow L.E.D.s the pack voltage is low and you need to recharge.
Battery storage indicator
NO
Yes, The storage is turned on if you click the button and the fuel gauge shows white L.E.D.s the pack is in storage mode.
Advanced charging protection
NO
Yes, if the pack individual cell voltage is too low when charging is started,the BMS will limit the incoming charge current to battery until the voltage is correct, then accept full supplied charge current
Voltage Overcharge Protection
NO
Yes, the overcharge protection circuit will activate when any cell voltage exceeds the factory set failsafe values.
Charging over current protection
NO
Yes, charging over current protection circuit will be activated when charging current reaches factory set failsafe values. The protection circuit will remain active until charger is disconnected.
Charging short circuit protection
NO
Yes, the protection circuit will cut off charging when it detects that the current reaches the factory set short-circuit protection limit. When protection is triggered all FETs will be turned off.
High Temperature Charge Protection
NO
Yes, if the pack temperature exceeds factory set values It will not charge. When the pack is back in the correct temperature range it will charge normally
Low Temperature Charge Protection
NO
Yes, if the pack temperature falls below factory set values the pack will not charge. When the correct temperature is back in range the pack will charge normally.
Secondary Charge Protection
NO
Yes, Tattu Plus 2.0 has a secondary charging protection circuit. If the first level circuit has a failure, the second level of protection will cut the charging circuit off
IIC communication port
NO
Yes, The IIC communication port is active. When you connect the batterypack to the computer software the IIC will allow you to read: pack voltage, individual cell voltage, rated capacity after full charge, remaining capacity, capacity percentage, cycle time, tem
